please dont rip this site

Signal transition events (normative) Each signal transition diagram has numbers corresponding to the events that cause the transitions. The following is a list of those events.

  1. Host sets extensibility request value on data bus: 00h for Nibble Mode, 01h for Byte Mode, etc.
  2. Host requests an IEEE 1284 mode transfer by setting IEEE 1284 Active(nSelectIn) high and HostBusy(nAutoFd) low.
  3. Peripheral indicates IEEE 1284 support by setting AckDataReq(PError), Xflag(Select), and nDataAvail(nFault) high, and PtrClk(nAck) low.
  4. Host sets HostClk(nStrobe) low to latch extensibility request value into peripheral.
  5. After waiting the minimum HostClk(nStrobe) pulse width, host sets HostClk(nStrobe) and HostBusy(nAutoFd) high to acknowledge the support by the peripheral of IEEE 1284 protocol.
  6. Xflag(Select) is set to reflect the support by the peripheral of the requested extension. Busy is set to indicate whether the peripheral can accept data from the host in the Compatibility Mode. For the Nibble and Byte Modes, the peripheral sets nDataAvail(nFault) to indicate whether data is available and AckDataReq(PError) to match nDataAvail(nFault).
  7. Peripheral sets PtrClk(nAck) high, informing the host that the four interface status signals are valid.
  8. Host sets HostBusy(nAutoFd) low to indicate that it can accept data.
  9. Peripheral places a nibble on the four status lines (low order nibble for first handshake, high order nibble for second handshake).
  10. Peripheral sets PtrClk(nAck) low to indicate that data is valid.
  11. Host sets HostBusy(nAutoFd) high to handshake with the peripheral and (in Nibble Mode) to indicate that it has received data and cannot accept more at the moment.
  12. Peripheral acknowledges receipt of data by the host by setting PtrClk(nAck) high.
  13. Host sets HostBusy(nAutoFd) low, indicating that it can accept the second nibble.
  14. Peripheral sets status lines to indicate if a subsequent peripheral to host byte is ready to transfer, and sets PtrBusy to indicate its current forward channel status.
  15. In Byte Mode, host places data bus in a high impedance state in anticipation of peripheral-to-host transfer. In the Nibble Mode, the data bus is undefined.
  16. In Byte Mode, peripheral places bytes on data bus.
  17. Host sets HostClk(nStrobe) low. This event may happen after the falling or rising edge of Ptr-Clk( nAck), i.e., events 9 and 11. It is defined in the diagrams to occur coincident with event 10. The peripheral shall not interpret this event as a latch signal for forward channel data.
  18. Host sets HostClk(nStrobe) high. It shall occur before or coincident with setting Host-Busy( nAutoFd) low (event 7).
  19. Peripheral sets nDataAvail(nFault) low to indicate data is available, and sets PtrClk(nAck) low.
  20. After waiting the minimum pulse width, the peripheral sets PtrClk(nAck) high to generate an interrupt to the host.
  21. Host sets HostBusy(nAutoFd) high to acknowledge the request of the peripheral.
  22. Peripheral sets AckDataReq(PError) low to acknowledge the host.

file: /Techref/io/parallel/ieee1284.htm, 3KB, , updated: 2002/1/23 14:37, local time: 2024/4/20 06:13,

 ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE!

<A HREF=""> ieee1284 signal reverse transfer sequence</A>

After you find an appropriate page, you are invited to your to this massmind site! (posts will be visible only to you before review) Just type a nice message (short messages are blocked as spam) in the box and press the Post button. (HTML welcomed, but not the <A tag: Instead, use the link box to link to another page. A tutorial is available Members can login to post directly, become page editors, and be credited for their posts.

Link? Put it here: 
if you want a response, please enter your email address: 
Attn spammers: All posts are reviewed before being made visible to anyone other than the poster.
Did you find what you needed?

  PICList 2024 contributors:
o List host: MIT, Site host, Top posters @none found
- Page Editors: James Newton, David Cary, and YOU!
* Roman Black of Black Robotics donates from sales of Linistep stepper controller kits.
* Ashley Roll of Digital Nemesis donates from sales of RCL-1 RS232 to TTL converters.
* Monthly Subscribers: Gregg Rew. on-going support is MOST appreciated!
* Contributors: Richard Seriani, Sr.

Welcome to!