By Charles Ader
;******************************************************************** ; ; Compiled with MAPLAB 4.12.12 ; ;******************************************************************** LIST p=16C54 ; PIC16C54 is the target processor crc_hi equ 00EH crc_lo equ 00FH STATUS equ 3 ; STATUS register F3 CARRY equ 0 ; Carry bit in status register ;******************************************************************** ; CRC Test Program ;******************************************************************** org 0h start clrf crc_hi clrf crc_lo movlw 080H ; crc_hi:crc_lo = 00 00 call CRC16 movlw 075H ; crc_hi:crc_lo = A0 01 call CRC16 movlw 08AH ; crc_hi:crc_lo = 27 A0 call CRC16 movlw 00BH ; crc_hi:crc_lo = DF A6 call CRC16 movlw 075H ; crc_hi:crc_lo = BD 1E call CRC16 movlw 0C7H ; crc_hi:crc_lo = EF FC call CRC16 movlw 0AAH ; crc_hi:crc_lo = D3 AE call CRC16 movlw 075H ; crc_hi:crc_lo = C3 D2 call CRC16 movlw 0C7H ; crc_hi:crc_lo = BA 82 call CRC16 movlw 055H ; crc_hi:crc_lo = F3 7B call CRC16 movlw 043H ; crc_hi:crc_lo = 1C 73 call CRC16 movlw 01CH ; crc_hi:crc_lo = 14 1c call CRC16 movlw 014H ; crc_hi:crc_lo = 00 14 call CRC16 goto start ; crc_hi:crc_lo = 00 00 ;******************************************************************** ; ; CRC-16 (x^16+x^15+x^2+x^0) ; No tables, No loops, No temporary registers used. ; ; Input: W = Data byte for CRC calculation ; crc_hi:crc_lo 16 bit CRC register ; ; Output: crc_hi:crc_lo updated. ; ; Notes: CARRY is trashed. ; DIGIT CARRY is trashed. ; ZERO is trashed. ; W is zero on exit. ; ; 30 instructions, 31 machine cycles per byte. ; ; Copyright (C) February 8, 2000. All Right Reserved. ; Charles Ader, PO Box 940 Pleasanton, California, USA. ; ; This code started out as an example program found in ; Dallas Semiconductor Application Note 27: ; ; Understanding and Using Cyclic Redundancy Checks ; with Dallas Semiconductor iButton(TM) Products. ; ; The application note shows an 8051 assembly language ; routine that calculates the same CRC as the hardware ; in the DS5001/2 secure micro. ; ;******************************************************************** CRC16 xorwf crc_lo,W ;W = input XOR old crc_lo xorwf crc_hi,W ;Swap old crc_hi with W xorwf crc_hi,F ; xorwf crc_hi,W ;new crc_hi = input XOR old crc_lo movwf crc_lo ;new crc_lo = old crc_hi ; ; Calculate parity of crc_hi, (input XOR old crc_lo), ; an place the result in carry. ; ; Save crc_hi in W and use crc_hi as a temp ; location so we can test bits. ; ; Note: We use INCF STATUS,F to compliment ; carry. This is safe because the XORWF ; will clear the zero flag if any of the ; INCF instructions are going to execute. ; ; The INCF can be executed a maximum of ; four times after the XORWF before the ; bits to the left of zero in status will ; be affected. ; ; We use INCF at most three time here. ; movf crc_hi,W ;Save crc_hi in W swapf crc_hi,F ;Trade nibbles xorwf crc_hi,F ;XOR high half byte with low rrf crc_hi,F ;Initialize Carry btfsc crc_hi,0 incf STATUS,F ;Compliment carry btfsc crc_hi,1 incf STATUS,F ;Compliment carry btfsc crc_hi,2 incf STATUS,F ;Compliment carry movwf crc_hi ;Restore crc_hi from W ; ; Use the parity of crc_hi, (input XOR crc_lo), ; to complete the CRC calculation. ; movlw 001H btfsc STATUS,CARRY ; If carry xorwf crc_lo,F ; flip bit 0 of crc_lo movlw 040H rrf crc_hi,F ; shift parity into crc_hi btfsc STATUS,CARRY ; if shift out is one xorwf crc_lo,F ; flip bit 6 of crc_lo rlf crc_hi,W ; unshift crc_hi into W xorwf crc_hi,F ; combine them rrf crc_hi,F ; shift parity back into crc_hi movlw 080H btfsc STATUS,CARRY ; if shift out is one xorwf crc_lo,F ; flip bit 7 of crc_lo retlw 0 ;******************************************************************** ; Power on reset ;******************************************************************** org 01FFH goto start end -------------End CRC16.ASM------------------
Here is the same CRC16 routine for the x86 and 8051
----------CRC16.C for x86 start------------------------ #include <stdio.h> /******************************************************************** CRC-16 (x^16+x^15+x^2+x^0) No tables, No jumps. Input: c = Data byte for CRC calculation usp_crc = pointer to 16 bit CRC register Output: CRC at pointer usp_crc is updated Copyright (C) February 11, 2000. All Right Reserved. Charles Ader, PO Box 940 Pleasanton, California, USA. This code started out as an example program found in Dallas Semiconductor Application Note 27: Understanding and Using Cyclic Redundancy Checks with Dallas Semiconductor iButton(TM) Products. The application note shows an 8051 assembly language routine that calculates the same CRC as the hardware in the DS5001/2 secure micro. ********************************************************************/ void crc16(unsigned short *usp_crc, unsigned char c) { unsigned short crc; /* use a local temp so the compiler will */ /* handle all the x86 pointer crap. */ crc = *usp_crc; _asm { mov al,c mov cx,crc XOR AL,CL MOV CL,CH MOV CH,AL LAHF NOT AH RCR AH,1 RCR AH,1 AND AH,1 XOR CL,AH RCR AX,1 SBB AH,AH AND AH,0x40 XOR CL,AH MOV AH,AL XOR AL,CH RCL AH,1 RCR AL,1 MOV CH,AL RCR AL,1 AND AL,0x80 XOR CL,AL mov crc,cx } *usp_crc = crc; } /****************************************************** * MAIN FUNCTION * *******************************************************/ main() { unsigned int crc; while(1) { crc = 0; /* crc = 0x0000 */ crc16(&crc,0x80); /* crc = 0xA001 */ crc16(&crc,0x75); /* crc = 0x27A0 */ crc16(&crc,0x8A); /* crc = 0xDFA6 */ crc16(&crc,0x0B); /* crc = 0xBD1E */ crc16(&crc,0x75); /* crc = 0xEFFC */ crc16(&crc,0xC7); /* crc = 0xD3AE */ crc16(&crc,0xAA); /* crc = 0xC3D2 */ crc16(&crc,0x75); /* crc = 0xBA82 */ crc16(&crc,0xC7); /* crc = 0xF37B */ crc16(&crc,0x55); /* crc = 0x1C73 */ crc16(&crc,0x43); /* crc = 0x141C */ crc16(&crc,0x1C); /* crc = 0x0014 */ crc16(&crc,0x14); /* crc = 0x0000 */ } } /* end of main */ ----------CRC16.C for x86 end ------------------------ ----------CRC16.A51 for 8051 start--------------------- ; ; From Dallas Application note 27 ; ; CRC-16 (x^16+x^15+x^2+x^0) ; No tables, No loops, No temporary registers used. ; ; This code is from Dallas Semiconductor Application Note 27: ; ; Understanding and Using Cyclic Redundancy Checks ; with Dallas Semiconductor iButton(TM) Products. ; ; This routine that calculates the same CRC as the hardware ; in the DS5001/2 secure micro. ;----------------------------------------------------------------------- NAME CRC_test ?DT?CRC_test SEGMENT DATA rseg ?DT?CRC_test CRCH: ds 1 CRCL: ds 1 ?CO?CRC_test SEGMENT CODE RSEG ?CO?CRC_test public CRC_test CRC_test: mov CRCH,#0 mov CRCL,#0 mov A,#080H call CRC16 mov A,#075H call CRC16 mov A,#08AH call CRC16 mov A,#00BH call CRC16 mov A,#075H call CRC16 mov A,#0C7H call CRC16 mov A,#0AAH call CRC16 mov A,#075H call CRC16 mov A,#0C7H call CRC16 mov A,#055H call CRC16 mov A,#043H call CRC16 ljmp CRC_test ;CALCULATE CRC16 IN PARALLEL TO THE GREATEST EXTENT PRACTICAL ; INPUT: BYTE TO BE INCUDED IN CRC CALCULATION IS IN ACC ; OUTPUT: CRCH:CRCL UPDATED TO INCLUDE THE NEW BYTE ; CRC16: PUSH ACC ;save this in case the caller needs it XRL A,CRCL MOV CRCL,CRCH ;put the high byte of the crc in its dest.. MOV CRCH,A ;save data xor low(crc) for later MOV C,P JNC CRC0 XRL CRCL,#001H CRC0: RRC A ;get the low bit in c JNC CRC1 XRL CRCL,#040H CRC1: MOV C,ACC.7 XRL A,CRCH ;compute the results for bits P...U RRC A ;shift them into place MOV CRCH,A ;and save them JNC CRC2 XRL CRCL,#080H CRC2: POP ACC ;and restore everything and return RET end ----------CRC16.A51 for 8051 end ---------------------
Comments:
xorwf Crc16 + 0, W; W = input XOR old crc_lo( writren at C, see above )[Hynek]; xorwf Crc16 + 1, W; Swap old crc_hi with W; xorwf Crc16 + 1, F; xorwf Crc16 + 1, W; new crc_hi = input XOR old crc_lo; movwf Crc16 + 0; new crc_lo = old crc_hi; ; Calculate parity of crc_hi, ( input XOR old crc_lo ), ; ; an place the result in carry.; ; Save crc_hi in W and use crc_hi as a temp; ; location so we can test bits.; swapf Crc16 + 1, W; Save crc_hi in W[Hynek]; xorwf Crc16 + 1, W; XOR high half byte with low[Hynek]; btfsc W, 1; Compute parity of bits 0 - 3 at bit 0[Hynek]; xorlw 1; b0 ^= b1[Hynek]; btfsc W, 2; [Hynek]; xorlw 1; b0 ^= b2[Hynek]; btfsc W, 3; [Hynek]; xorlw 1; b0 ^= b3[Hynek]; andlw 1; W = parity[Hynek]; ; Use the parity of crc_hi, ( input XOR crc_lo ), ; ; to complete the CRC calculation.; xorwf Crc16 + 0, F; flip bit 0 of crc_lo; rrf W, W; Carry - parity[Hynek]; rrf Crc16 + 1, F; shift parity into crc_hi; movlw 0x40; [hynek]; btfsc STATUS, Carry; if shift out is one; xorwf Crc16 + 0, F; flip bit 6 of crc_lo; rlf Crc16 + 1, W; unshift crc_hi into W; xorwf Crc16 + 1, F; combine them; rrf Crc16 + 1, F; shift parity back into crc_hi; movlw 0x80; btfsc STATUS, Carry; if shift out is one; xorwf Crc16 + 0, F; flip bit 7 of crc_lo;+
file: /Techref/microchip/crc16ca.htm, 12KB, , updated: 2021/7/6 08:58, local time: 2024/10/8 14:02,
44.220.184.63:LOG IN ©2024 PLEASE DON'T RIP! THIS SITE CLOSES OCT 28, 2024 SO LONG AND THANKS FOR ALL THE FISH!
|
©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions? <A HREF="http://piclist.com/techref/microchip/crc16ca.htm"> PIC Microcontroller Bit Math Method - CRC</A> |
Did you find what you needed? |
PICList 2024 contributors:
o List host: MIT, Site host massmind.org, Top posters @none found - Page Editors: James Newton, David Cary, and YOU! * Roman Black of Black Robotics donates from sales of Linistep stepper controller kits. * Ashley Roll of Digital Nemesis donates from sales of RCL-1 RS232 to TTL converters. * Monthly Subscribers: Gregg Rew. on-going support is MOST appreciated! * Contributors: Richard Seriani, Sr. |
Welcome to piclist.com! |
.