please dont rip this site
From: mjohnson at netcom4.Netcom.COM (Mark Johnson)

If you know what you are doing, you can build wirewrapped
boards that operate above 100MHz.  I myself have done so;
I've got a couple that run at 150MHz with no trouble.

On the other hand, if you don't know what you are doing,
you can screw up almost any technology, including wire
wrap, printed circuit board, proto-plugboard, and airbridge.

   "It's not the sword, it's the swordsman"
   "It's not the sword, it's the swordsman"
   "It's not the sword, it's the swordsman"
   "It's not the sword, it's the swordsman"

Here are a few ways to screw up a wirewrapped project,
so as to make it fail even at low frequencies:

   1.  Don't use a board with a ground plane.

   2.  When wrapping the positive and negative supply
       pins of IC's, use wires longer than 0.75 inch.
       The longer the better; these aren't high
       frequency signals, they are just DC supplies.

   3.  Don't install ceramic bypass capacitors at
       every chip

   4.  Use digital logic chips having very fast
       edge speeds (dV/dt), such as 74S, 74AS, 74F,
       and, best of all, 74FACT.

   5.  Daisy chain the ground wires: wrap from the
       off-board ground connector, to the ground pin
       on the first chip, to the ground pin on the
       second chip, to the ground pin on the third
       chip, and so forth.

   6.  Freely mix analog and digital circuitry on
       a wirewrap board,  Be sure the analog part
       us used as a routing area for digital signal
       wires, and vice versa.  Share supply and
       ground connections between the two.

If you scrupulously follow these rules, then you can
brag to your friends that you have built a wirewrap
board that failed, not at 20MHz, but at 1MHz.  Won'tthey be impressed!

file: /Techref/wirewrap/hownot.htm, 2KB, , updated: 2000/7/6 14:01, local time: 2024/3/28 08:58,
TOP NEW HELP FIND: 
44.212.39.149:LOG IN

 ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?
Please DO link to this page! Digg it! / MAKE!

<A HREF="http://piclist.com/techref/wirewrap/hownot.htm"> How not to wire wrap</A>

After you find an appropriate page, you are invited to your to this massmind site! (posts will be visible only to you before review) Just type a nice message (short messages are blocked as spam) in the box and press the Post button. (HTML welcomed, but not the <A tag: Instead, use the link box to link to another page. A tutorial is available Members can login to post directly, become page editors, and be credited for their posts.


Link? Put it here: 
if you want a response, please enter your email address: 
Attn spammers: All posts are reviewed before being made visible to anyone other than the poster.
Did you find what you needed?

  PICList 2024 contributors:
o List host: MIT, Site host massmind.org, Top posters @none found
- Page Editors: James Newton, David Cary, and YOU!
* Roman Black of Black Robotics donates from sales of Linistep stepper controller kits.
* Ashley Roll of Digital Nemesis donates from sales of RCL-1 RS232 to TTL converters.
* Monthly Subscribers: Gregg Rew. on-going support is MOST appreciated!
* Contributors: Richard Seriani, Sr.
 

Welcome to piclist.com!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  .